How to Activate Ethernet Port on Wall? | Quick Ethernet Port Activation Guide for You

While using an internet connection, our primary concern is getting a faster internet speed. Although WiFi connections can get the job done, they are comparatively less potent than Ethernet connections. Once you use an Ethernet connection, you won’t readily want to get back to a WiFi connection anymore. 

There are a few ways to establish an Ethernet connection and doing it from an active Ethernet port on the wall is worth mentioning. But in this case, you must have at least an Ethernet port on your wall.

Now if you’re wondering how you can activate the Ethernet port on your wall, you’ve come to the exact place. This post contains the necessary information about this matter, just stick to the post till the end. 

Steps for Activating Ethernet Port on Wall

There are two requirements to activate the wall’s Ethernet port. The first one is you must have an Ethernet port, and the second one is the port status is completely fine.  

Therefore, if you don’t have an Ethernet port on your wall, first of all, you need to install an Ethernet jack on your wall. Here, you can get the whole procedure to do this by yourself. Just apply it accordingly and save some money.

Now, if you have the port on your wall, check if the port is in perfect condition. It’s a common fact that most times the technicians don’t wire it from the beginning. If it’s the same case as yours, you have to wire it first and establish the connection in the port. 

1. Wiring the Ethernet Outlet

To do so, take the following steps accordingly – 

Step 1: Start by taking off the outlet. You will need a flat screwdriver to unscrew and pry out the outlet case. Afterward, take out the cable. 

Step 2: Cut the cable’s outer sheathing from the last 1-2 inches.

Step 3: After that, on the keystone connector, thread each wire according to the color-coded slots. The cable should have four pairs of wires with similar colors. Just align each wire with its suitable slot.

Step 4: Next, make use of a punch-down tool to force the wires down and enable conductivity. 

Step 5: Then cover the exposed part of the connector with its protective cover plates.

Step 6: After that, place the connector into the wall plate where the hole remains. You can confirm that it’s perfectly attached when you hear a clicky sound.

Step 7: Finally, screw the wall plate properly so that the cable stays safe from outside impact.

2. Enable the Ethernet Connection

Now that you successfully installed or wired the Ethernet outlet, it’s time to establish an Ethernet connection. To do that –

Step 1: Ready the device that you want to connect to the wall Ethernet port. This could be a computer, gaming console, or any other device that has an Ethernet port.

Step 2: Then connect a suitable Ethernet cable (by length, category, etc) from the Ethernet port on your device to the Ethernet port.

Step 3: Now, let the device recognize the Ethernet connection. Once it is recognized, you should see an icon indicating that the device is connected to the network.

Step 4: Finally, test the connection by opening a web browser and accessing a website. If the website loads correctly, then the Ethernet port on the wall is now activated and working correctly.

Step 5: If the connection is unavailable then navigate through Control Panel > Network and Sharing Center > Change the adapter settings and enable your Ethernet connection here.

If you successfully have applied the methods stated above, you successfully have activated the Ethernet port on your wall and made an internet connection with that port.

Bonus Points

After doing all the stuff, if you find that your Ethernet port is still inactivated, then the problem is somewhere else. There are a few possible causes and one of them is to blame in this case. One, the port cable wires are improperly placed or placed in the wrong slots. Check them again and align them correctly. Two, maybe the lines aren’t intact perfectly. Use a tone tracer to fix it. Last, the lines are clogged by old paint. Therefore, scrape off the paint gently without any damage. 

Frequently Asked Questions (FAQs)

How do I know if my Ethernet port is working on my wall?

The process is pretty easy. Go to the part of your computer where the Ethernet port is. Check for a solid green or blue light that is next to the blue cable. If you notice the light is lit then surely the port is working.

Does the Ethernet wall jack slow speed?

Basically, the Ethernet wall jack doesn’t slow the speed, rather it increases the speed. But here’s a catch. If you use the wrong type of Ethernet cable, then it can possibly slow your connection speed.

What is the Ethernet jack in the wall called?

Typically, the Ethernet jack that is used in the wall is the RJ45 connector. They are also called modular connectors in some cases. 

Conclusion

That is all about activating an Ethernet port on a wall. The method is pretty simple and very convenient to apply. Just make sure that you’re doing it as instructed. Let us know if this post helps you to activate your port and if you have further questions.